Saltar al contenido / Skip to content

Ayon Spirit V EN

INDEX ESPAÑOL
TECHNICAL REPORT · V1.8.5.2 · 18 NOVEMBER 2026

Ayon Spirit V — Architecture, circuit, measurements and technical assessment

Analysis of a KT150/KT170 push-pull integrated amplifier based on an internal inspection, a power test and external documentation. Special attention to DMP, the power supply, the transformers and the limits of the evidence.

Sources: supplied technical video, interior photograph and manufacturer documentation · Updated 18 November 2026

Quick summary

What is analysed: Ayon Spirit V, KT150/KT170 architecture, DMP control, power supply and output power.

What we know: ≈60.5 W/8 Ω at 1 kHz near clipping in the KT150 unit inspected.

What we do not know: THD+N versus power, output impedance and conduction class at full power.

Who it is for: readers of technical audio and owners of loudspeakers with variable electrical load.

Conclusion: an interesting design, but without enough data to claim metrological superiority.

0. Executive summary

Ayon Spirit V valve integrated amplifier, exterior view
Exterior view of the Ayon Spirit V. Tap to enlarge and use zoom.

The Ayon Audio Spirit V is an Austrian valve integrated amplifier with two KT150 per channel, 12AX7/6SN7 drivers, output transformers with ultralinear taps as described in the technical inspection, fixed bias with automatic control and DMP damping adaptation. The technical inspection of a KT150 unit provides internal data that do not appear in the commercial specification sheet.

MEASURED-EXT: the technician reports approximately 22 V RMS into an 8 Ω resistive load at 1 kHz, close to visible clipping: 60.5 W calculated. He does not report THD+N or continuous power with both channels driven.

Relevant finding: the examined unit uses an adjustable global feedback path taken from the 4 Ω output, even with DMP in OFF according to the technician's description. This requires qualifying the commercial «0 dB» specification.

Main uncertainty: measurements are missing for the Spirit V of output impedance, damping factor, THD+N versus power in both modes (up to 40 W in triode and 65 W in pentode mode, per the declared power), IMD and behaviour with reactive loads.

Editorial criterion. Power at clipping is not presented as power at 1 % THD; measurements from the Spirit III are not carried over to the Spirit V.

1. Sources, scope and method

1.1. Primary source: inspection and tests

The basis for the internal analysis is the video «Ayon Spirit V — Review, analysis, technical details and measurements», roughly 37 minutes long. The work used its Spanish transcript, which contains automatic-recognition errors (for example «ION» for Ayon, «vías» for bias). Technical denominations are normalised only when the context is unambiguous.

The video shows a repaired KT150 unit; it must not be assumed that its circuit or components are identical to those of every KT170 revision.

1.2. Classification of evidence

The same evidence categories as the Magnat MA 900 report are used. CONFIRMED identifies data appearing in official documentation, but does not mean that its performance has been independently measured. MEASURED-EXT is reserved for third-party instrumental measurements: the video reports a voltage close to 22 V RMS into 8 Ω at 1 kHz, near clipping, without a full distortion curve. REPORTED-EXT identifies information communicated by third parties without a verifiable instrumental measurement. Technical explanations are separated from facts through PROBABLE, HYPOTHESIS and ND.

1.3. Complementary sources

Ayon's commercial specification sheet and reviews from HiFi.nl, Soundrebels, HiFi-IFAs and Alpha Audio. Listening impressions are kept separate from instrumental results. Links are collected in the sources annex.

2. Specifications and revisions

Specifications: general sheet, 2023 price list and the inspected unit must be distinguished.
ParameterValueSource / notes
TopologyStereo push-pullCONFIRMED; inspection
Output valves4 × KT150 or KT170CONFIRMED; the video unit uses KT150
Small-signal valves2 × 12AX7 + 2 × 6SN7OBSERVED in the video
ModesTriode / «pentode» (sheet) · ultralinear taps ≈43 % (video)CONFIRMED (commercial naming) / REPORTED-EXT (taps); see note
Power, general sheet65 W pentode mode (commercial naming) / 40 W triode per channelCONFIRMED; no THD specified
Power, 2023 KT150 list70 W pentode mode / 45 W triodeHistorical commercial document; not standardised without conditions
Power, 2023 KT170 list75 W pentode mode / 50 W triodeHistorical commercial document
Nominal output impedance4 Ω and 8 Ω tapsCONFIRMED; not equivalent to Zout
Input sensitivity500 mV RMSCONFIRMED; sensitivity for maximum power per the sheet
Input impedance100 kΩ at 1 kHzCONFIRMED
Declared response10 Hz–60 kHz (−3 dB)CONFIRMED; power condition ND
Feedback«0 dB» declared / DMP observableDocumentary discrepancy; see §6
Dimensions and weight480 × 370 × 250 mm; ≈33 kgCONFIRMED
Documentary discrepancy — operating mode. The commercial documentation identifies the operating modes as pentode and triode. The external technical analysis describes connections to output-transformer taps at roughly 43 %, consistent with an ultralinear configuration. Without the full electrical schematic and a direct verification of the connections, it cannot be established whether the commercial «pentode» designation describes conventional pentode operation or a variant with ultralinear taps. In this report, «ultralinear» is used for the 65 W mode only because the video describes it as such. That transformer ultralinear tap and the global feedback (see §6) are distinct mechanisms.

2.1. What changes with KT170

Ayon described a power-supply and driver upgrade to accommodate KT170. The historical figures of 70 vs. 75 W represent only 0.30 dB of nominal difference; 45 vs. 50 W in triode represent 0.46 dB. On their own they do not justify an audible improvement or a higher price.

2.2. Terminology

The KT150 is a beam power tetrode. «Ultralinear» describes the connection of its screen grid to a tap on the primary; «triode» describes the equivalent triode connection. Neither of those terms on its own determines class A or AB.

3. Audio circuit and transformers

Ayon Spirit V interior: red printed circuit boards, a bank of eight capacitors, filter chokes, relays, resistors and power and control wiring
Figure 1. Ayon Spirit V interior. Photograph provided for the report; component identification based on the technical video inspection. Tap to enlarge and use zoom.

3.1. Signal stages

Stages and functions of the signal chain
BlockDescriptionEvidence
First stage12AX7 in common cathode with active load; one triode acts as the load of the otherOBSERVED / partial reverse engineering 24:06
Driver / phase splitter6SN7 in differential configuration; in-phase and anti-phase signalsOBSERVED 23:13
CouplingTwo capacitors per channel towards the power stage; drive-balance adjustmentsOBSERVED 23:45
OutputTwo KT150 per channel, push-pull; relays switch triode / ULOBSERVED 25:56
Functional diagram of the Ayon Spirit V, per channelMain path: input, 12AX7, 6SN7 differential phase splitter, two KT150 push-pull, output transformer and 4 and 8 ohm outputs. Ultralinear taps and DMP return, the latter as an inferred path not verified.Inputsignal12AX7first stage6SN7differential2 × KT150push-pullOutputtransformer4 Ω8 ΩUL taps ≈43 %DMP: exact return and summing point not verifiedFunctional connection described or observedExact path inferred / ND
Figure 2. Simplified functional diagram of one channel. Solid line: architecture described or observed in the video; dashed line: DMP path shown for orientation, without a service schematic. The connections are not equivalent to a complete electrical schematic. The diagram is limited to the signal path: it does not show the power supply or the control circuits. UL tap of 43 %: value reported by the technician, without a documented measurement procedure.

3.2. Output transformer

The technician reports ≈5,300 Ω plate to plate as the reflected primary impedance and 43 % for the ultralinear taps (25:29). This is the nominal load reflected to the primary, not a 5.3 kΩ DC resistance.

The assessment of low leakage inductance and small parasitic capacitance comes from the technician; the transcript does not provide numerical measurements of primary L, leakage inductance, distributed capacitance or phase response.

3.3. Square-wave test

The technician shows a roughly rectangular signal with small transients at the edges (34:35). This is a favourable observation, but the frequency, amplitude, exact load and time scale are not sufficiently documented in the transcript. It does not allow the bandwidth to be calculated or stability with capacitive loads to be guaranteed.

See Figure 2: signal path

4. Measurements and reproducible calculations

Results attributable only to the unit and conditions described.
ParameterResultCondition / limitationEvidence
Output voltage≈22 V RMS8 Ω, 1 kHz, 65 W mode (ultralinear per the video), near clippingMEASURED-EXT 30:53
Derived power60.5 WP = 22²/8; THD not specifiedCALCULATED
Difference vs. 65 W−0.31 dB10 log10(60.5/65)CALCULATED
Primary load≈5.3 kΩValue reported by the technicianREPORTED-EXT 25:44
Ultralinear tap43 %Value reported, no measurement procedureREPORTED-EXT
THD+N at 1/5/10/20 WNDNo distortion analyser shownND
Damping factorNDNo Zout given per DMP positionND
Response with reactive loadNDNo standardised test availableND
P = V² / R = 22² / 8 = 60.5 W

The video describes the visible clipping as level is increased. The figure is not equivalent to 60.5 W at 1 % THD. The test does not document a THD+N versus power sweep, nor the thermal duration of the run.

4.1. Ideal primary excursion

Assuming an ideal transformer, 60.5 W and a primary load of 5,300 Ω:

V plate-to-plate (rms) = √(60.5 × 5300) ≈ 566 V; peak excursion per half-primary ≈ 400 V

This is not a measurement of plate voltage. It ignores losses, magnetising inductance, dynamic valve impedance and load variations.

4.2. Comparison with the declared 65 W

The agreement between power at clipping and the general specification is reasonable, but it does not allow the linearity to be judged. An amplifier can reach its nominal power at a THD higher than is tolerable for a high-fidelity comparison.

Calculated vs. declared powerComparison of 60.5 watts calculated from 22 volts RMS near clipping and 65 watts declared; harmonic distortion, output impedance and damping factor are unknown.Power: calculated vs. specification≈60.5 W calculated · 22 V RMS / 8 Ω, near clipping60.5 W65 W · manufacturer specification65 WDifference: −0.31 dB · non-standardised power criteriaTHD+N: NDZout: NDDF: ND
Figure 3. The 60.5 W figure is a calculation based on the described test, not a certified power at a given THD threshold. The three lower quantities lack a comparable independent measurement.

5. Power supply, filtering and startup

5.1. Architecture

The inspection distinguishes permanent control supply, main audio supply, high-voltage taps and sequencing relays (14:17). The technician estimates the final B+ at around 470 V and describes an initial startup with a lower-voltage tap, followed by relay switching.

5.2. High-voltage capacitors

8 × 220 µF / 450 V are described (14:57). With two equal capacitors in series, each pair is ideally 110 µF and withstands a combined 900 V rating only if voltage sharing is adequate. If four pairs were in parallel on the same node, the equivalent would be 440 µF; the distribution between nodes is not verified.

5.3. Choke filtering

A main C–L–C filter and a second choke dedicated to the driver are described (17:48). This favours ripple reduction and decoupling, but the L values, winding resistances and residual-ripple measurements are missing.

5.4. Filaments and grounding

According to the technician, the 12AX7 and 6SN7 use regulated 6.3 V DC, while the KT150 use 6.3 V AC with a balanced reference. The reported consumption of ≈2 A per KT150 implies about 50.4 W in the four power filaments alone (6.3 × 8 A). Separate per-channel ground returns and dedicated volume-control connections are visible (19:15).

Functional diagram of the power supply and startupControl supply, high-voltage supply, C L C filtering, driver tap, filaments and relay sequencing. Dashed lines indicate inferred functional connections.Power supply and control · functional diagramMains / powertransformerRectificationand B+ supplyC–L–C filter≈470 V reportedKT150 stageper channelSecond Lfor driver12AX7 / 6SN7input stagesPermanent controland sequencingRelays / progressivestartupFilaments6.3 VDC: 12AX7 / 6SN7Balanced AC: KT150Solid blue: described blocks · dashed orange: inferred interconnection. SGND and PE not shown.
Figure 4. Functional summary of the power supply described in the video, not an electrical schematic or wiring map. B+ ≈470 V is a reported estimate; exact connections, voltages and relay sequence: ND.

6. DMP, feedback and output impedance

6.1. Apparent contradiction with «0 dB»

The commercial sheet mentions 0 dB of feedback. In contrast, the technician identifies a path from the 4 Ω secondary to the first voltage stage and explains that the DMP selector modifies the global feedback (5:48). He explicitly states that a small amount of feedback remains in OFF, not a completely open loop.

Without the schematic and measurements, it cannot be determined whether the commercial figure corresponds to a specific configuration, to a naming convention or to a different revision.

6.2. Selector positions

DMP selector positions and evidence limits
PositionSupported informationNot demonstrated
OFFMinimal feedback per the technicianExactly 0 dB or open loop
1Alternative feedback settingExact NFB magnitude and Zout
2Alternative feedback settingExact NFB magnitude and Zout

Reviews associate more intense DMP positions with difficult loads. The transcript is not enough to assign a numerical damping value to each position.

6.3. Power does not necessarily decrease

Increasing negative feedback usually lowers the closed-loop gain. With the same 500 mV input the output voltage may fall; that does not prove a decrease in maximum achievable power if the drive is increased. The test must be repeated to the same clipping threshold in each position.

6.4. Load-interaction model

ΔdB = 20 log10[(Zmax/(Zmax+Zout)) / (Zmin/(Zmin+Zout))]
CALCULATED examples, not measurements of the Spirit V.
Hypothetical ZoutSpeaker Z 5 ΩSpeaker Z 15 ΩDifference
0.5 Ω−0.83 dB−0.29 dB0.54 dB
1 Ω−1.58 dB−0.56 dB1.02 dB
2 Ω−2.92 dB−1.09 dB1.84 dB

This simplified resistive model does not include phase angle, frequency dependence of Zout or transformer non-linearity.

See Figure 2: functional representation of DMP

7. Biasing, control and safety

7.1. Auto-Fixed-Bias

The technician describes fixed bias with a negative grid voltage controlled by a Microchip microcontroller, based on current sensing through low-value cathode resistors (16:45). This is not classic cathode self-bias. A front-panel instrument and a selector allow each of the four valves to be checked.

7.2. Startup and shutdown sequences

A countdown close to one minute on power-up and a supervised shutdown sequence are described. The technician warns against cutting power during the sequence (12:11). The exact scope of the configuration loss and its recovery procedure has not been demonstrated by a systematic test.

7.3. SGND and protective earth

The SGND switch changes the relationship between signal ground and earth, according to the inspection (4:31). It can help with ground loops, but the chassis protective earth must never be removed. Without a service schematic, altering internal connections or bypassing protections is not recommended.

Safety. According to the estimate reported in the video, B+ circuits may operate at around 470 V and the capacitors may retain dangerous charge after disconnection. Any internal intervention is a job for a qualified technician.

8. Class A, AB and interpretative limits

After studying how the biasing is adjusted and how the amplifier is protected, a different question remains: for what portion of each cycle does each valve conduct as power increases? That is the question that separates classes A and AB.

Ayon presents the Spirit V as class A, while some reviews describe triode in class A and ultralinear in class AB. The video does not document quiescent current or conduction angle up to maximum power.

With 5.3 kΩ plate to plate and ≈60.5 W, the ideal voltage excursion is high; that is not enough to demonstrate class AB. Nor is a static bias reading enough to demonstrate class A up to 60 W. Instantaneous currents of both branches, plate and screen voltages, and load conditions are required.

For this reason, the rigorous classification of the Spirit V must remain ND as regards the maximum power sustained in class A. Triode/ultralinear and class A/AB describe different properties.

9. Listening, speakers and applications

9.1. What the reviews say

HiFi.nl describes a powerful and relatively neutral sound; Soundrebels points to resolution capability and differences between modes; Alpha Audio provides a comparative listening. These are testimonials in different systems, not measurements or blind tests of superiority.

9.2. Power and dynamics

Illustrative power-demand scenario, not a measurement of the Ayon–MoFi combination. As an example, a pair of MoFi SourcePoint 10 Master Edition coaxial high-fidelity speakers is taken, listened to at 3 m. The measured sensitivity is 89.2 dB/2.83 V/1 m, averaged between 300 Hz and 3 kHz, according to Erin’s Audio Corner on Spinorama. For the calculation, 89.2 dB/W/m is adopted as an approximation, assuming a resistive 8 Ω reference impedance; the actual impedance is not assumed to be constant. The manufacturer declares 91 dB/2.83 V/1 m. These are assumptions, not measurements: −9.5 dB from 1 m to 3 m, +4 dB room and +3 dB for the sum of two channels.

Under those assumptions, peaks of 95/100/102 dB require approximately 6.8/21.6/34.2 W per channel. The results change with distance, room acoustics and music content; they do not predict the maximum SPL of the Spirit V in any room.

9.3. MR-A-01

What MR-A-01 is. It is a passive three-way speaker project, with a crossover designed for a relatively uniform response and a predicted minimum impedance close to 4.9 Ω. It is used here as an example of a real load, not as a speaker tested with the Ayon.

For the MR-A-01 project (predicted impedance minimum ≈4.9 Ω), it is particularly relevant to measure Zout and response with a real load in the three DMP positions. A change in damping may alter a carefully tuned axial response. It is incorrect to select the DMP position exclusively by nominal impedance.

9.4. High-output sources

The 500 mV nominal sensitivity indicates considerable overall gain. With 2 V RCA or 4 V XLR sources, it is advisable to check input headroom and effective gain, especially when using the direct input. According to the technician, the XLR connection is internally converted into an unbalanced signal (21:12); that alone does not demonstrate the common-mode rejection quality of its input interface.

10. Comparison, price and maintenance

10.1. Technical comparison

The amplifiers with a dedicated Nauscopio report are linked in the table; the remaining analyses are in the technical reports index.

The power values are each manufacturer's specifications unless an external measurement is indicated. ND means that no independent, comparable measurement with documented conditions is available here. The absence of a value does not prove worse performance.

Documentary comparison, not a performance ranking. Zout: output impedance; DF: damping factor.
AmplifierDeclared powerComparable THD+NComparable ZoutComparable DFNote
Ayon Spirit V65 W pentode / 40 W triodeNDNDNDVideo: ≈60.5 W/8 Ω near clipping, THD not quantified
Fezz Titania MK260 WNDNDNDComparable DF: ND. Sheet DF: >40, non-standardised conditions
Cayin Jazz 9050 W UL / 28 W triodeNDNDNDSheet THD data without a homogeneous independent test
Cayin CS-55A40 W ULNDNDNDPower quoted under its own criterion
Acronos RS-125 WNDNDNDSingle-ended topology: different from push-pull

To compare THD+N, Zout or DF, identical load, frequency, level, output tap and operating configuration would be required. A catalogue DF is not a comparable measurement if those conditions are missing.

10.2. Price and second-hand purchase

Verifiable current price: ND. Without a dated and traceable offer, no current price or price range is quoted here. For a used unit, it is advisable to check the KT150/KT170 revision, serial number, repair history, valve condition, Auto-Fixed-Bias operation and parts availability.

10.3. Maintenance and cost of ownership

Maintenance and pre-purchase checks
ItemDocumentary statusRecommended check
Power valve set4 × KT150 in the version analysed; KT170 revisions exist. Replacement cost: NDRequest a quote for a matched set and a bias check
Signal valves12AX7 and 6SN7 in the described circuit. Total replacement cost: NDVerify the number and exact references of the unit
Valve lifetimeND for this unit and usage conditionsAssess hours, electrical condition and settings; do not fix a universal period
Warranty and service in SpainND for a specific date, distributor and serial numberConfirm coverage, service centre and parts supply in writing
Idle consumption and heatND: no reproducible measurement of mains input or thermal dissipation is availableMeasure absorbed power at thermal steady state; ensure ventilation
Residual noiseND under comparable laboratory conditionsMeasure with terminated inputs and a known level reference

The circuit includes a microcontroller, relays and bias control. The possibility of obtaining repair and spare parts is therefore an important consideration for a long-term purchase.

11. Conclusions and verdict

Architecture: technically ambitious construction, with an elaborate power supply, differential drivers, ultralinear transformers and bias control.

Power: for the KT150 unit in the video, approximately 60.5 W/8 Ω is calculated from 22 V RMS into 8 Ω near clipping, in line with the general specification of 65 W, but without a quantified THD criterion.

DMP: a feature of great interest for speakers with variable impedance; its effect has not been instrumentally characterised in the examined documentation.

Caveat: electrical superiority cannot be claimed over Fezz Titania MK2, Cayin Jazz 90 or other candidates without homogeneous tests of THD+N, Zout, noise and reactive load.

Nauscopio verdict. The Spirit V deserves consideration as a high-end valve integrated amplifier, but its price and commercial claims should be judged with reproducible measurements. The priority is to obtain the output impedance in OFF/1/2 and the power at 1 % THD in triode and ultralinear.
ANNEX A — SOURCES AND TRACEABILITY

Annex A. Sources and traceability

A.1. Primary sources

Technical video: Ayon Spirit V — review, inspection and measurements. Video transcript and interior photograph provided for the report.

Manufacturer: Ayon Audio — Spirit V specifications · Ayon price list dated 1 January 2023 (copy hosted on Scribd). Commercial specification sheets may change; record the revision of each unit.

A.2. Reviews and cross-checking

HiFi.nl — René van Es · Soundrebels — Spirit V · HiFi-IFAs — Spirit V · Alpha Audio — amplifier comparison.

Not all external publication and access dates could be verified. The report's update date should not be interpreted as the publication date of those references. The historical commercial price list quoted corresponds to 2023 and does not certify current prices.

Example in §9.2. MoFi SourcePoint 10 Master Edition measurement data published by Erin’s Audio Corner on Spinorama. Manufacturer specification (91 dB) according to Audio Advisor.

A.3. Editorial record

Authorship: maty @nauscopio + IA (research, calculations, writing and layout). Version: V1.8.5.2. Date: 18 November 2026.

Scope: technical synthesis based on the supplied inspection and the identified sources; no in-house laboratory test was performed.

A.4. Change history

V1.8.5.2 (EN): English translation of V1.8.5.2 (ES); Spanish version at ayon-spirit-v.html. V1.8.5.2: pentode naming in tables and summary, source for the §9.2 example and A.2 wording. V1.8.5: editorial cleanup, note on operating mode, internal links and print compatibility. V1.8.4: editorial close: unified version, corrected SVG attributes, verified links and precise evidence labels. V1.8.3: references to other reports added. V1.8.2: accessibility fixes and new power-supply and power figures. V1.8: ND-homogeneous comparison, reworked §10 and functional diagram. V1.7: simplified CSS and JavaScript. V1.6: JSON-LD and dedicated script for annexes. V1.5: collapsible annexes.

ANNEX B — PENDING MEASUREMENT PROTOCOL

Annex B. Pending measurement protocol

Proposed protocol for independent measurements
TestProposed conditionsPurpose
THD+N versus power1 kHz; 0.1–65 W; 4/8 Ω; both channelsClean power and curve shape
Multifrequency THD+N20 Hz / 1 kHz / 10 kHz at 1/5/10/20 WLinearity and transformers
Output impedance20 Hz–20 kHz; DMP OFF/1/2; 4/8 Ω tapsDamping factor and response
Square wave100 Hz / 1 kHz / 10 kHz; resistive/reactive loadStability and transients
NoiseTerminated inputs; 1 W referenceSNR and hum
Conduction currentPer branch and per mode; safe measurementActual class A / AB

All tests require documentation of mains voltage, warm-up, valve condition, DMP configuration, output tap, power and distortion threshold.

Ayon Spirit V · Nauscopio · V1.8.5.2 · 18 November 2026