Saltar al contenido / Skip to content

Jadis Ôde vs Acronos M-1 and Acronos RS-1

INDEX ESPAÑOL
Jadis Ôde vs Acronos M-1 / RS-1 · Comparative report · Nov 2026

Jadis Ôde vs Acronos M-1 and Acronos RS-1

A study comparing a class A push-pull amplifier with four KT120 —the Jadis Ôde— against two JC Valvular single-ended ultralinear designs: the Acronos M-1 with KT120 and the Acronos RS-1 with KT150. The report separates confirmed data from declared figures and non-determinable values, and pays particular attention to the preamp chain, real power and the loudspeaker.

Sources: official Jadis data sheet, Lyric Audio, Audio Planet, JC Valvular M-1, Acronos RS-1 (Nauscopio) and Et Sona.

Jadis Ôde 4×KT120 vs Acronos M-1 and RS-1 SE KT150.

Figure 0 — Cover: Jadis Ôde 4×KT120 vs Acronos M-1 and RS-1 SE KT150.

Reading guide — what is known, what is claimed and what remains unmeasured

What they are. The Jadis Ôde is a class A push-pull integrated amplifier with 4× KT120 and 2×25 W (some commercial descriptions mention 2×30 W and KT88/KT120 depending on the source or dealer; see the version note in §1). The Acronos M-1 is a single-ended ultralinear design with KT120, declared at 20 W (18 W at 0.01% THD). The Acronos RS-1 is a single-ended ultralinear design with KT150, declared at 25 W maximum at 0.5% THD and 18 W at 0.01% THD; both figures are declared without an independent laboratory test. CONFIRMED / REPORTED-EXT

The structural difference. The Ôde uses two power valves per channel in push-pull; the Acronos use one valve per channel in single-ended. This topology difference affects output-transformer design, the handling of DC current and efficiency trade-offs. It does not, by itself, establish bass control, frequency response into a specific loudspeaker or an audible sonic character without comparable measurements. CONFIRMED

Preamp valves. Ôde: ECC82 and ECC83. M-1: NOS 12AT7 and ECC83. RS-1: NOS EC86 as preamp and NOS ECC803S as driver and cathode follower, with one KT150 per channel.

Priority. The Ôde offers more functions and 25 W nominal; the M-1 and RS-1 allow single-ended architectures to be studied. Without comparable measurements, timbre cannot be predicted and no specific margin over a real loudspeaker can be guaranteed.

Quick guide — documented differences and their limits

A quick guide to deciding without reading the whole report.

Jadis Ôde · Push-pull

PP 4×KT120 · 2×25 W · 5 RCA + remote · auto bias · 25 kg MIXED DATA: SEE §1
Can be considered with speakers below 90 dB and Zmin 4 Ω, although its response into the load still has to be measured (§4.1). An ideal balanced push-pull topology does not require the air gap normally used in SE transformers; the actual Ôde OPT construction has not been verified (§3.1). Wide valve stock (§5.4). Versatile in functions; electrical compatibility to be verified.

Acronos M-1 · SE KT120

SE KT120 · 20 W / 18 W@0.01% · 3 RCA · 14 kg MIXED DATA: SEE §1
Sensitivity and impedance to be checked for the specific level and distance. Compact. A straightforward single-ended design. Calculate §4.2

Acronos RS-1 · SE KT150

SE KT150 · 18 W@0.01%/25 W@0.5% · NFB DF50 · custom OPT · 130 mA bias MIXED DATA: SEE §1
NOS EC86 + ECC803S (Annex B no. 1). 3 RCA, Muting. A single-ended design with maintenance requirements still to be confirmed.

Criterion: there is no universal 90 dB boundary. Selection depends on real sensitivity, distance, level, crest factor, output tap and load. Declared nominal power and DF do not replace comparable tests. Calculator · Measurement and ND matrix.

0. Executive summary

The Jadis Ôde is a French class A pure push-pull valve integrated amplifier with four KT120, a valve preamp, five RCA inputs, remote control and automatic bias. It declares 2×25 W, 10 Hz–40 kHz at −3 dB and 300 VA maximum. Price announced by the dealer: €7,990 VAT included (see conditions and validity in Annex D). CONFIRMED

The Acronos M-1 is a single-ended class A pure ultralinear design with KT120, 20 W declared and 18 W RMS at 0.01% THD at 1 kHz. It shares with the RS-1 the same weight, dimensions, input impedance, sensitivity and THD figure.

The Acronos RS-1 is an evolution of the M-1: it replaces the KT120 with a KT150 per channel, raises maximum power to 25 W and uses custom output transformers different from those of the M-1. It declares 18 W at 0.01% THD and 25 W at 0.5% THD. The damping factor of 50 is published by Et Sona from information supplied by the manufacturer, without independent measurement. REPORTED-EXT

A plausible risk, not a finding. The Ôde and the Acronos are not equivalent alternatives under a different brand. They represent two different philosophies: push-pull with four KT120 on the one hand, single-ended ultralinear with one power valve per channel on the other. The choice must begin with the target level, listening distance, real speaker sensitivity and load compatibility; topology alone does not predict the sound.

1. Method, evidence and limits

1.1 Sources

The report draws on the official Jadis data sheet, Lyric Audio, Audio Planet, the JC Valvular M-1 data sheet, the Acronos RS-1 report on Nauscopio, the Et Sona review and direct communication from the manufacturer.

1.2 Master table

ParameterJadis ÔdeAcronos M-1Acronos RS-1
TopologyPush-pull, class A pure CONFIRMEDSingle-ended, class A pure ultralinear CONFIRMED — typical UL tap 40–43%, actual % NDSingle-ended, class A pure ultralinear CONFIRMED — typical UL tap 40–43%, actual % ND
Power valves4× KT120KT1202× KT150, one per channel
Declared power2×25 W (some sources mention 2×30 W with KT88/KT120 depending on the dealer; see the version note in §3.1)20 W25 W maximum
Operating classClass A pure CONFIRMEDClass A pure CONFIRMEDClass A declared; actual class ND — 130 mA alone does not define the operating point
Declared THDND18 W at 0.01% at 1 kHz18 W @0.01%; 25 W @0.5%
Preamp valves1× ECC82 and 2× ECC83NOS 12AT7 and ECC831× NOS EC86 + 1× NOS ECC803S per channel (6 valves in total) CONFIRMED
BiasAutomaticND130 mA per KT150, adjustable CONFIRMED
NFBNDYes, Acronos house policyYes; depth and type ND
Inputs5 RCA3 RCA3 RCA with Muting
RemoteYesNoNo
Response10 Hz–40 kHz at −3 dB20 Hz–45 kHz20 Hz–40 kHz
Weight25 kg14 kg14 kg
Consumption300 VA maximumND195 W
Dimensions430×370×220 mm according to the official Jadis data sheet CONFIRMED; other sizes at dealers cannot be applied without identifying the version45×26×11 cm REPORTED-EXT45×26×11 cm REPORTED-EXT
Input impedanceND (not to be confused with sensitivity)100 kΩ REPORTED-EXT100 kΩ REPORTED-EXT
Input sensitivity300 mV CONFIRMED (Jadis)100 mV CONFIRMED (JC Valvular; conditions ND)100 mV REPORTED-EXT (Et Sona; conditions ND)
Price€7,990 VAT includedNDND

1.3 Evidence level

LabelMeaning
CONFIRMEDSpecification or official manufacturer documentation, including direct communication from JC Valvular.
OBSERVEDVisible in photographs or on the nameplate.
REPORTED-EXTPublished by a reliable third party (Et Sona, dealer) without independent verification.
PROBABLEA coherent inference, not verified.
CALCULATEDA result obtained from an explicit formula.
NDNot determinable with the available evidence.

Evidence status — what is known, what is assumed, what must be measured

Documented in official sources or observationsDeclared but unverified (REPORTED-EXT via Et Sona)Would decide the purchase (pending measurement)
SE ultralinear topology, KT150 per channel, EC86 preamp + ECC803S driver + cathode follower, custom OPT, RF/EMI filter, Muting, chassis 45×26×11 cm, 14 kg, 195 W, 3 RCA inputs25 W maximum, 18 W RMS @0.01% THD @1 kHz, 0.5% THD associated with 25 W maximum, DF 50 (figure supplied by JC Valvular and published by Et Sona, not an Et Sona measurement), RS-1 sensitivity 100 mV (conditions ND; also appears in the official M-1 data), 100 kΩ input, 4/8 Ω1. Conditions and magnitude of the 100 mV sensitivity (do not assume 1,000 mV) 2. NFB in dB and its type (global from the secondary, local, cathode or combined) 3. THD versus power/frequency/load curve 4. Zout versus frequency 5. Actual B+ and UL %
Reading: this is a traceability table. Et Sona's publication discloses specifications supplied by the manufacturer; it does not validate them experimentally. DF 50 should be read as a catalogue figure equivalent to a Zout of 0.16 Ω into 8 Ω, without a published frequency, method or reactive behaviour. The 0.5% THD associated with 25 W maximum and the 18 W @0.01% @1 kHz are two isolated points, not a curve.

1.5 What each datum proves and what decision it allows

DatumVerifiable scopeDecision it authorises
Ôde with remote and five inputsDocumented functional featureCompare ease of use
SE KT150 with custom OPT in the RS-1Architectural descriptionCompare topologies, not demonstrated sound
DF 50 reported for the RS-1Reported datum, not an external measurementRequest a Zout(f) measurement; do not claim superior control
18 W at 0.01% THD declaredIsolated specification at 1 kHzConditional arithmetic comparison, not a common bench
MR-A-01 at 89 dB/W/mCalculation hypothesis, not measured sensitivitySPL scenarios, not a real compatibility verdict
Prices and industrial costsPrices only with date and evidence; BOM and margins hypotheticalCompare verifiable prices; explore scenarios, not business profits

2. Electrical comparison: power, THD, impedance and control

2.1 Declared power and comparison conditions

The Ôde is rated at 25 W per channel according to Lyric/Bluebird (4×KT120); some dealer sources describe 2×30 W class A with KT88/KT120 and KT150 compatibility — see the version note in §3.1. The M-1 is rated at 20 W, 18 W RMS @0.01% THD at 1 kHz. The RS-1 declares 25 W maximum, 18 W @0.01% and 25 W @0.5% THD (full test conditions ND). For the Acronos units the load impedance is not confirmed; the report uses 8 Ω as a working hypothesis.

Measurement status: THD, S/N, Zout and P@1% THD remain ND for all three. No common bench exists.

2.2 Comparable electrical evidence matrix

Reading: declared performance and laboratory tests are not equivalent. Powers specified at different THD values do not form a like-for-like comparison. CALCULATED applies only to quantities derived from explicit assumptions.

QuantityJadis ÔdeAcronos M-1Acronos RS-1What it allows you to conclude
Nominal power25 W declared, class A20 W declared25 W maximum declaredCatalogue figures; THD and load conditions are not homogeneous
18 W at THD 0.01% / 1 kHzNDDeclared by an external sourceDeclared by an external sourceNot our own measurements; independent verification required
Power at THD+N 1%, 4 and 8 ΩNDNDNDComparable clean power cannot be ranked
Zout from 20 Hz to 20 kHzNDNDNDInteraction with real impedance cannot be ranked
Verified damping factorNDNDND; DF 50 reportedThe RS-1's communicated value requires measurement and stated conditions
Response into the MR-A-01 RLC loadNDNDNDThe most electrically neutral unit cannot be identified
Comparable residual noise and humNDNDNDNo hierarchy of low-level behaviour can be established
Authorised tap for 6 ΩThe official Ôde guide specifies a factory setting for loudspeakers rated from 4 to 8 Ω, including 6 Ω. Confirm that the guide applies to the unit and its version.To be verified in the manualTo be verified in the manualA precondition for any real comparison
What changes a purchase: an unauthorised tap prevents the test; Zout(f) and the response into the same load reveal the interaction; power at the same THD+N threshold reveals the reserve; noise and THD at 1 W inform about normal use. Until those measurements exist, the technical choice remains provisional.

2.3 Output impedance, NFB and load control

In an ideally balanced push-pull stage, cancellation of the DC flux allows an output transformer to be designed without the air gap normally required in single-ended operation. The actual air-gap arrangement in the Ôde has not been documented here. This structural principle does not, by itself, establish lower Zout or better bass control. The RS-1 declares DF 50, which corresponds to Zout 0.16 Ω into 8 Ω; this is a figure supplied by JC Valvular and published by Et Sona (REPORTED-EXT, not an Et Sona measurement), a catalogue value without a published frequency, method or reactive behaviour. An effective comparison remains ND, pending a Zout versus frequency measurement.

Sensitivity, gain and feedback — Annex B no. 1: taking 25 W into a resistive 8 Ω load as a hypothesis, 100 mV requires an approximate total gain of 43.01 dB; 1,000 mV requires 23.01 dB. JC Valvular also publishes 100 mV for the M-1; an erratum in the RS-1 cannot be declared without clarification from the manufacturer. The feedback intervals of 21–29 dB and 41–49 dB quoted in previous versions depended on an assumed, undocumented open-loop gain, and do not allow any conclusion about the compatibility or incompatibility between sensitivity, DF 50 and declared THD. Independent measurements of gain, Zout(f) and distortion versus power and load are needed to check it. CALCULATED with hypotheses
ScenarioOption by functions (conditional)Reason
≥90 dBRS-1 or M-1Power to be calculated according to distance, target SPL and load
86–89 dBJadis Ôde25 W nominal; the specific margin depends on the calculation and the tap used
Large rooms / high volumeJadis ÔdeThe requirement is calculated; it does not depend on m² alone
Vocals, jazz, chamber, acousticRS-1Aesthetic or architectural preference, not measured sonic superiority
Reactive loads, Zmin and phase — generic SE Zout(f): in some single-ended designs, Zout(f) may vary with frequency: below 50 Hz because of the output transformer's inductance and saturation, above 10 kHz because of parasitic capacitance. It interacts with the real Zload(f) as a voltage divider — Vout = Vin × Zload/(Zout+Zload) — which modifies the effective frequency response. The absence of feedback, or a low amount of it, tends to penalise speakers with Zmin below 5 Ω and high phase. An EPDR of 2–3 Ω is a generic example range for a difficult speaker, not a value measured on the MR-A-01 (its impedance and phase curves are still pending). Without those curves, and without Zout versus frequency for the three amplifiers, neither the effect nor any hierarchy can be quantified; the Ôde's push-pull advantage is structural (no gap), not a measurement of bass control.

3. Architecture: push-pull, single-ended and transformers

3.1 Jadis Ôde: push-pull KT120

The Ôde uses two KT120 per channel in push-pull. Because the two branches conduct in phase opposition, their quiescent currents cancel in the primary of the output transformer. Under ideal balance, this removes the usual requirement for an air gap and may allow a smaller core for comparable design constraints. The actual transformer construction and any advantage in output power, output impedance or load control remain unverified for this model.

3.2 Acronos M-1: SE KT120

The M-1 is a single-ended class A pure ultralinear design. One power valve per channel conducts throughout the cycle, so its quiescent current flows permanently through the primary of the output transformer. This calls for an air gap in the transformer and makes the OPT the most determining component of the final result.

3.3 Acronos RS-1: SE KT150

The RS-1 keeps the M-1's single-ended ultralinear architecture but moves from the KT120 to the KT150 and declares 25 W maximum. Its output transformers are custom and different from those of the M-1. It incorporates negative feedback, an RF/EMI filter on the IEC C14 input and two threaded fuse holders. Et Sona describes the construction as a 1.5 mm carbon steel chassis, solid wood panels and 22 mm feet. REPORTED-EXT

RS-1 preamp signal flow (CONFIRMED — JC Valvular via Et Sona): EC86 (high-gm triode, voltage gain) → ECC803S section 1 (driver) → ECC803S section 2 (cathode follower / low-Zout buffer) → KT150 ultralinear output stage. A cathode follower can reduce the drive impedance, but it does not by itself demonstrate the available grid current or a distortion figure; both require measurements and a schematic.

3.4 Practical implications: advantages and limits

AspectÔde push-pullM-1 / RS-1 single-ended
Quiescent current cancellationYesNo; requires an OPT with a gap
EfficiencyDepends on class, bias and transformer; push-pull allows other excursion conditionsIn SE class A it is usually lower, but no figure is derived here
Transformer size per wattSmallerLarger
Bass controlA structural advantage of the push-pull OPT; the effective comparison remains NDDependent on the OPT, the feedback and the load
Usual characterNot deducible from topology: listening and measurement NDNot deducible from topology: listening and measurement ND

3.5 Transformers: direct current and air gap

The figure below helps visualise why a single-ended design needs a transformer with an air gap when it has to carry direct current, whereas a balanced push-pull cancels most of the quiescent flux. In single-ended operation, the tube's DC current generates an uncancelled constant flux, which risks saturating the core; an air gap (GAP) is introduced to prevent saturation, but it reduces inductance and calls for a larger core. In push-pull, the two opposing 180° currents cancel (Φ1+Φ2≈0): there is no net DC flux, no gap is needed, and the core works more efficiently.

Comparison of SE transformer core with gap vs PP with flux cancellation — Jadis Ôde 25 kg vs Acronos 14 kg
Figure 2.5 — Conceptual comparison of push-pull and single-ended transformer operation, not a verified drawing of either product. Left: ideal DC-flux cancellation in a balanced push-pull stage, illustrated alongside the Jadis Ôde (25 kg declared total mass); actual core geometry, air gap and internal mass distribution are unverified. Right: illustrative single-ended transformer associated with the Acronos (14 kg declared total mass); its actual lamination arrangement and air-gap dimension are ND. The reported 130 mA bias refers to the RS-1 KT150 operating point and does not establish the transformer core design. Click to enlarge.

3.6 Preamp valves, driver and maintenance

ModelChain per channelDocumented functionExpected character
Jadis ÔdeECC83 + ECC82 + KT120×2Exact role ND without the schematic; ECC83 gain / ECC82 driver distribution is presumedSound ND; wide replacement availability
Acronos M-1NOS 12AT7 + ECC83 + KT120Exact role ND without the schematic; pending identificationSound ND without a level-matched test
Acronos RS-11× NOS EC86 + 1× NOS ECC803S + 1× KT150 per channel (6 valves in total, see the Acronos RS-1 report on Nauscopio)EC86 preamp; ECC803S driver and cathode follower CONFIRMEDSound ND; preamp topology documented, declared THD unmeasured

3.1 Ôde: ECC83 and ECC82

A more conventional combination: huge availability in both current production and NOS.

3.2 M-1: 12AT7 and ECC83

The 12AT7 has a lower mu than the 12AX7 but delivers higher current, which is consistent with a driver role; this does not by itself allow speed or audible timbre to be predicted.

3.3 RS-1: EC86 and ECC803S

The EC86 is a triode used for signal amplification; the ECC803S belongs to the ECC83/12AX7 family. Neither designation demonstrates timbre, noise level or distortion of the complete amplifier. The use of NOS valves reduces ease of substitution.

Maintenance note: the use of NOS EC86 and ECC803S in the RS-1 is attractive but less common. Confirm compatibility and the bias procedure with JC Valvular before replacing.

4. MR-A-01 suitability: power, crests and reserve

4.1 Reference headroom with two speakers at 3 m

CALCULATED Report reference scenario: an 89 dB/W/m speaker, listening at 3 m, two speakers (≈+3 dB stereo sum, not constant room gain), 80 dB continuous SPL and 15 dB crest factor, i.e. a 95 dB peak.

StepCalculationResult
SPL with 1 W per speaker at 3 m89 − 20·log10(3) = 89 − 9.5479.46 dB
Continuous power for 80 dB (2 speakers, +3 dB)10^((80−79.46−3)/10)0.57 W/channel
Peak power (crest +15 dB)0.57 × 10^(15/10)≈ 17.96 W/channel
Target with +3 dB reserve17.96 × 10^(3/10)≈ 35.8 W/channel
Reference: 100 dB peak with the same speaker113.3 W for one speaker; 56.8 W/channel with two speakers (+3 dB)100 dB peak ≈ 56.8 W/channel, without reserve
Scenario with +4 dB room gain (hypothesis from the Acronos RS-1 report on Nauscopio)95 dB ≈ 7.13 W/channel; 100 dB ≈ 22.6 W/channel25 W → only 0.44 dB of margin at 100 dB peak
Correct reading: with 89 dB/W/m at 3 m in free field, a 100 dB peak requires ≈56.8 W/channel (two speakers). The approximate 22.6 W/channel figure from previous versions only holds with the ≈+4 dB room-gain hypothesis drawn from the RS-1 report, now explicitly declared as such: under it, 25 W leave barely 0.44 dB of margin at 100 dB peak. The 80 dB continuous + 15 dB crest scenario requires ≈17.96 W/channel, and with +3 dB reserve → 35.8 W/channel. Under these hypotheses, none of the three reaches the target with reserve; JC Valvular recommends ≥90 dB for SE as an orientation criterion, not as a universal boundary.

JC Valvular recommends ≥90 dB for single-ended designs. For a structured decision on the MR-A-01 (6 Ω nominal, simulated Zmin ≈4.9 Ω, 89 dB/W/m as a hypothesis pending measurement), see the suitability index of 15 valve amplifiers in this blog, with its five-criteria matrix and the tap instruction as an admissibility condition. Full detail is available in calculators #2 and the Initial method notice.

4.2 Power and SPL calculator

Quick pre-calculated reference (2.5 m, 2 speakers +3 dB, 80 dB continuous + 15 dB crest = 95 dB peak target):
Speaker sensitivitySPL 1W/2.5mRequired peak powerWith the RS-1's declared 18 W at 0.01% THDWith the Ôde's 25 W
85 dB77.0 dB~31.3 W/channel−2.4 dB short−1.0 dB short
88 dB80.0 dB~15.7 W/channel+0.6 dB margin+2.0 dB margin
92 dB84.0 dB~6.3 W/channel+4.6 dB margin+6.0 dB margin
Orientation calculation without complex impedance or room gain. For the report's 89 dB/W/m at 3 m: 79.46 dB @1W, 17.96 W/channel peak, 35.8 W target with +3 dB reserve.

CALCULATED An intermediate version between the simple slider calculator and the full Rev 9.0.1 in acoustic calculators #2. It keeps the continuous + crest + reserve logic, but without the 2.83 V converter or impedance checking. Ideal for comparing Jadis and Acronos in 30 seconds.

Methodological notice: this is an orientation mathematical model. It does not replace a measurement of power, distortion or behaviour into a reactive load. The results depend on the sensitivity, distance, stereo sum and room conditions entered, and refer to an idealised 8 Ω resistive load. The MR-A-01 has 6 Ω nominal and a simulated minimum close to 4.9 Ω: the calculator does not consider the 4/8 Ω tap, the variation of power with load, the complex impedance, the output impedance or thermal compression, so its results are SPL estimates, not guaranteed power into that speaker.
dB. The report uses 89 dB/W/m. Accepts a comma.
m. Loss = −20·log10(d). The report uses 3 m.
Incoherent sum in the room.
dB SPL at the listening position.
Above the continuous level.
Margin above the peak.
If you type 25 manually, the margin is calculated with 25 W, but it does not distinguish between the Jadis 25 W and the RS-1 25 W @0.5%. Use the buttons to set the preset.
Note: the presets do not share measurement conditions (different THD values or ND). The result is an arithmetic margin against the figure entered, not a comparison of clean power between amplifiers.
SPL @1W at chosen distance—
Continuous P—
Peak SPL—
Peak P (cont+crest)—
Target P with reserve—
Arithmetic margin vs power entered—
—

Formulas: SPL1W,d = S1W − 20·log10(d) · Pcont = 10^((SPLcont − SPL1W,d − G)/10) · Ppeak = Pcont·10^(C/10) · Ptarget = Ppeak·10^(H/10). Free-field propagation model (−20·log10 d), idealised 8 Ω resistive load and no correction for real impedance, output tap or room. For the full version with the 2.83 V converter and ND impedances, see Rev 9.0.1.

5. Use, maintenance and safety

5.1 Convenience

The Ôde is the more convenient of the three: 5 inputs, remote control and auto bias. The M-1 and RS-1 have 3 RCA inputs and no DAC, phono stage or Bluetooth. The RS-1 declares 100 mV sensitivity — see unknown no. 1 in Annex B (100 mV declared: check the conditions and do not infer NFB from sensitivity).

5.2 Bias and valves

The Ôde simplifies this area with automatic bias. The RS-1 declares fixed adjustable bias at 130 mA per KT150 and has eight visible trimmers, although the full procedure and the function of each trimmer are not published. KT150: 70 W maximum plate dissipation (Tung-Sol datasheet, not 60 W). An idealised voltage excursion CALCULATED with hypotheses according to the Acronos RS-1 report on Nauscopio: 25 W and 130 mA allow an idealised voltage excursion of about 385 V to be calculated if a 130 mA current limit is adopted; this does not determine B+ nor support the 478 V previously proposed. The hypothetical products 400×0.130 = 52 W and 450×0.130 = 58.5 W do not constitute measured plate dissipation: Va at quiescent, plate Ia separated from screen current, screen conditions and bias point are all unknown. ND actual operating point and dissipation.

Warning: the RS-1 plate voltage is not published and must not be inferred from the bias. Do not open the chassis or intervene in the unit: bias adjustment and any internal measurement are the responsibility of the manufacturer or a qualified technician; the high-voltage supply stores lethal energy even when switched off.

5.3 Good practice

  • Respect the ventilation required by the manufacturer; in the absence of specific instructions, avoid enclosed spaces and check the external temperature without touching the valves.
  • Do not stack equipment on top or enclose it in closed cabinets.
  • Use compatible 4 or 8 Ω speakers.
  • Confirm any KT150/KT120 or preamp substitution with the manufacturer.
  • Check for possible mechanical hum (a plausible risk from class A + 100 Hz rectifier peaks + magnetostriction + a compact chassis, not a finding measured on this particular unit) after one hour of operation before installing the amplifier on a shelf.

5.4 Long-term maintenance cost and availability matrix

A financial and logistical breakdown of periodic replacement. It does not include exact prices, given market variation; it indicates relative demand and availability.

ItemJadis ÔdeAcronos M-1Acronos RS-1Notes
Power valves4× matched KT120 (quartet)2× KT120 (1 per channel, matched pair recommended)2× KT150 (1 per channel, matched pair)A quartet is more demanding than a pair; the KT150 is less stocked than the KT120
MatchingMatched quartet; auto bias partially compensatesPair, manual bias NDPair, fixed 130 mA adjustable biasThe Ôde's auto bias simplifies the task; the RS-1 requires the 130 mA procedure to be confirmed by the manufacturer
Preamp valvesECC82 + 2× ECC83 — wide current stock, NOS optionalNOS 12AT7 + ECC83 — NOS scarcer than current ECC831× NOS EC86 + 1× NOS ECC803S per channel (6 valves in total, RS-1 report) — scarce NOS and high costEC86/ECC803S NOS: verify the batch and substitutions with JC Valvular before buying
Critical consumablesStandard fusesStandard fuses2 threaded fuse holders + IEC C14 RF/EMI filterThe RS-1 adds an EMI filter and input Muting
5–10 year availabilityHigh (KT120 in current production)High to medium (KT120 + NOS 12AT7)Medium (limited KT150 production + NOS EC86/ECC803S)Recommended NOS spare stock for the RS-1
Relative power replacement cost★★★ (4 tubes)★★ (2 tubes)★★★½ (2× KT150 > KT120)★ = lower relative cost
Relative NOS preamp cost★★★★★★★The RS-1 is more dependent on NOS
Reading: Ôde = more tubes but easier to source; M-1 = balance; RS-1 = fewer power tubes than the Ôde, but more expensive and reliant on scarce NOS preamp valves. For long-term use, consider laying in a stock of EC86/ECC803S NOS when buying the RS-1.

6. Assessment based on evidence, not sonic predictions

AxisJadis ÔdeAcronos M-1Acronos RS-1
ArchitecturePush-pull 4×KT120SE KT120 ultralinearSE KT150 ultralinear
Useful powerGreater reserveLimited25 W maximum declared, 18 W at 0.01% THD; margin depends on the target
Bass controlStructural push-pull OPT advantage; effective comparison NDDependent on the OPTDependent on the OPT and the actual NFB
Sonic character (expected, without comparative listening)ND without level-matched listeningND without level-matched listeningND without level-matched listening
FunctionsRemote, 5 inputs, auto bias3 inputs3 inputs, Muting, NFB and custom OPT
Preamp replacementVery easy (ECC83/ECC82)Easy (ECC83/12AT7)Less common NOS (EC86/ECC803S)
Technical riskLowModerateModerate to high, due to unmeasured figures
Example scenarios by sensitivity, impedance and room (without measured Zout or power; these are NOT certified compatibilities):
Speaker / RoomÔde 25W PPM-1 20W nominal SERS-1 25W SE
≥90 dB, Zmin ≥5 Ω, room ≤20 m²Requires SPL calculation and the authorised tapConditional on load and levelReserve ND; calculate SPL and load
87–89 dB, Zmin 4–5 Ω, room 20–30 m²Assess first; margin NDRequires calculation and measurementRequires calculation and measurement
≤86 dB, Zmin <4 Ω or room >30 m²Power/load unverifiedNot conclusive without a specific caseNot conclusive without a specific case
What cannot be concluded with the available data (ND): actual Zout versus frequency for all three, THD versus power/frequency/load curve, power at 4 Ω, frequency response at 1 W and nominal, SNR/residual hum, actual dissipation and actual UL %, and RS-1 sensitivity under known conditions. Everything declared REPORTED-EXT without independent verification.

6.1 Limits of sonic prediction without comparative listening

Without controlled listening or comparative measurements, this is extrapolation by topology and valves, not a verdict: the Ôde uses push-pull while the M-1 and RS-1 are single-ended. They are different architectures, but the harmonic spectrum, the frequency response into a real load and level-matched listening are not available in comparable form. It is not appropriate to infer "soundstage", "micro-detail", "texture" or "authority" from the name of the valve, the preamp or the topology. Personal preferences may motivate an audition; they cannot replace one. The margin depends on measured sensitivity, distance, target level, crests, Zout and load.

7. Provisional decision and limits of the comparison

7.0 Conditions before choosing

NeedDocumentary optionPending condition
More inputs and a remoteÔde, a demonstrated functional advantageVerify the version and the specific condition
SE KT120 with few valvesM-1 by architectureUseful power, noise and response into the load must be measured: ND
SE KT150 with particular preamp electronicsRS-1 by architectureVerify DF and THD; input sensitivity and load
Greater neutrality and MR-A-01 compatibilityND among the threeMeasure the same RLC load, the authorised taps and the same protocol
Scope: this report does not prove that the RS-1 figures are false. It proves that, with the publicly available data, they are extraordinary and require experimental verification.
If your priority is…Recommendation
The most complete and versatile amplifierJadis Ôde
A compact single-ended KT120 designAcronos M-1
A single-ended design with KT150 and custom OPTAcronos RS-1
Low sensitivity or high volumeJadis Ôde
≥90 dB, moderate distance and intimate listeningAcronos RS-1 conditional
Maximum maintenance simplicityJadis Ôde

7.1 What cannot be concluded

Precision: the 25 W declared for the RS-1 at 0.5% THD are not a measurement equivalent to its 18 W declared at 0.01% THD; no single threshold is a universal synonym for "clean" power. The ≥90 dB recommendation for SE designs is JC Valvular's orientation criterion, conditional on sensitivity, distance, crest factor and impedance — not a universal boundary.
What the author would buy and why (a personal position, not a measurement): in my MR-A-01 scenario — 6 Ω nominal, simulated Zmin 4.9 Ω, hypothetical 89 dB/W/m and listening at 3 m — I would not declare an electrical winner: all three fall below 35.83 W/channel with reserve, and none has been measured into this load. By functions I would first audit the Jadis Ôde; for architectural interest, the RS-1; and as a single-ended alternative, the M-1. Choosing on the strength of a supposed EC86/ECC803S "texture" is not supported without a comparative audition.
  • There are no comparable independent measurements of THD, S/N, Zout or P@1%.
  • The RS-1 DF 50 is a figure supplied by JC Valvular and published by Et Sona (REPORTED-EXT), not a verified independent measurement. It is equivalent to a Zout of 0.16 Ω into 8 Ω without a published frequency or method.
  • THD 0.01% at 18 W @1 kHz and 0.5% associated with 25 W maximum: two isolated points (REPORTED-EXT via Et Sona), without a THD versus power/frequency/load curve or IEC 60268-3 conditions. A single point does not characterise an amplifier.
  • The RS-1 NFB depth and type are unknown.
  • It cannot be stated that one model sounds better without controlled listening and identical speakers.
  • Without Zmin and phase curves for the MR-A-01, or Zout versus frequency for the three amplifiers, electrical compatibility can only be estimated (see §4.2 and §2.3).

7.2 Buyer's toolkit

Checklist before buying:

  • Speakers: record effective sensitivity, Zmin and phase — the 90 dB boundary does not by itself determine compatibility. Calculate power, check the authorised tap and measure where possible.
  • Room: is the distance ≥2.5 m? Use the calculator in §4.2 to estimate the margin.
  • Maintenance: matched KT120/KT150? Access to NOS EC86/ECC803S? Are you familiar with the RS-1's 130 mA bias?
  • Daily use: do you need a remote and 5 inputs? Only the Ôde has them.
  • Ventilation: is it in accordance with the manufacturer's manual? Is there mechanical hum after one hour?
Nauscopio verdict: Ôde = a more complete push-pull; M-1 = a compact SE KT120; RS-1 = a more ambitious SE KT150 with custom OPT, NFB, Muting and EMI filter. The choice depends on listening level, distance, sensitivity, complex load and functions; there is no measured electrical winner.

7.3 FAQ — 12 key questions

Which one has a remote and five inputs?

The Ôde: five inputs and remote control, according to the official data sheet. The M-1 and RS-1: three RCA inputs; Et Sona describes Muting on the RS-1. Master table.

What bias does the RS-1 use?

130 mA per KT150 is reported, without measurement of Va, plate or screen current. This is not equivalent to knowing B+ or the actual dissipation. Only intervene through the manufacturer or a qualified technician. §5.2.

Are the RS-1's 25 W and the Ôde's 25 W the same?

Comparable THD, load and frequency conditions have not been documented: the Ôde publishes 25 W class A; the RS-1 reports 18 W at 0.01% THD and 25 W at 0.5%. These are declarations, not a laboratory comparison. §2.1.

100 mV for the RS-1, or 1,000 mV?

Et Sona publishes 100 mV for the RS-1 and JC Valvular also publishes 100 mV for the M-1. At 25 W/8 Ω hypothetical, this corresponds to 43.01 dB of gain; 1 V would correspond to 23.01 dB. It does not demonstrate an erratum nor determine NFB, THD or DF. Annex B.

Is the RS-1's DF 50 measured?

No independent measurement is published in the sources used. It is a specification communicated to the media. DF 50 into 8 Ω formally equals 0.16 Ω only under undocumented conditions. §2.3.

What is the difference between push-pull and single-ended?

Balanced push-pull compensates the transformer's DC currents; single-ended must manage DC flux and normally needs an air gap. This does not allow acoustic quality or audible timbre to be deduced. §3.

Which valves do they use?

Jadis: 4×KT120, ECC82 and ECC83. M-1: KT120, 12AT7 and ECC83. RS-1: KT150, EC86 and ECC803S. Future availability and compatible substitutes should be confirmed with the manufacturer. §5.4.

For which room and speaker?

Square metres or a 90 dB sensitivity cut-off are not enough. Enter level, distance, crest and reserve in §4.2 and verify the tap and the impedance curve. The figure does not include the complex load.

Why 25 kg versus 14 kg?

These are equipment masses, not transformer measurements. The previous estimated breakdown adds up to 27.48 and 15.85 kg: it does not reproduce the declared weight. The heavier-transformer scenario is explained as a hypothesis in Annex C.

Is the Jadis Ôde 25 or 30 W, KT120 or KT88?

The current official data sheet states 25 W class A, four KT120, 300 mV and 430×370×220 mm. There are commercial descriptions with KT88 and 30 W that have not been reconciled; no specific electrical revision should be asserted without documentation.

What would the author choose?

For the MR-A-01 and the declared target, none certifies the 35.83 W/channel with reserve or equivalent performance into a reactive load. The Ôde stands out for functions; the M-1 and RS-1 for single-ended topology. The sonic choice remains pending measurement and a level-matched audition. §7.1.

ANNEXES

Annex A — Sources

Annex B — Pending measurements

PriorityMeasurementPurpose
1Conditions of the 100 mV sensitivity published for the RS-1 (the 1,000 mV hypothesis is not verified)Determine the actual gain and the conditions of the figure; it does not allow the loop or the viability of THD/DF to be inferred
2RS-1 NFB depth and type in dB (global from the secondary, local, cathode or combined)Verify the coherence of the declared THD and DF
3THD versus power/frequency/load curveA single 18 W @0.01% @1 kHz point does not characterise; validate 18 W @0.01% and 25 W @0.5% with IEC 60268-3
4Zout versus frequency 20 Hz–20 kHz with 4/8 Ω and EPDRCheck DF 50 (Zout 0.16 Ω/8 Ω) with real loads; DF at 1 kHz resistive does not predict 20 Hz or reactive loads
5Actual plate voltage and UL %, and actual dissipationCheck the quiescent point and the actual excursions: 385 V would be an idealised excursion under assumptions, not a measured or inferred B+
Electrical safety warning. Bias adjustment (130 mA per KT150, a specification attributed to JC Valvular) and any internal measurement of the RS-1 or the Ôde must be carried out by the manufacturer or a qualified technician, following the specific schematic and procedure for each unit. This report does not publish or recommend procedures for opening, measuring or discharging capacitors: the high-voltage supply stores enough energy to be lethal even with the unit switched off, and a CAT II rating does not make an internal intervention safe. The cathode resistor value, measurement point and trimmers can only be established with the official schematic.

B.2 Reproducible test specific to the MR-A-01

Before comparing, confirm from the manual the authorised tap of each amplifier for a 6 Ω nominal speaker. Do not use the same physical tap if the manufacturers prescribe different taps; record the setting chosen, keep the same test load and declare the results separately.

TestMinimum documented conditionsDecision it allows
Power and distortionTHD+N versus power, 20 Hz / 1 kHz / 10 kHz; 4 and 8 Ω resistive, both channels; power at 1% and 3%Real signal margin at the same criterion
Zout(f) and DF20 Hz–20 kHz, specified method, same NFB state, output taps recordedElectrical interaction and inference of DF at each frequency
Response into the MR-A-01 loadSame RLC network approximating Z(f) and phase, same reference voltage; measure deviation from resistive loadElectrical tonal deviation, not a sonic judgement
Noise and low powerTHD+N at 1 W, output residual and SNR with declared reference/weighting, both channelsLow-level behaviour
Continuity10 W / 60 min and 80% of P@1% / 10 min, with appropriate thermal monitoringCheck stability without extrapolating from nominal power

A repeatable RLC load does not replace acoustic measurements of the MR-A-01 in its room. No measured values are available to complete this table: all remain ND until tests are performed.

ANNEX C — MASS AND TRANSFORMER ESTIMATES

Annex C — Construction and weight hypotheses

Scope: internal masses calculated from apparent dimensions and photographs are not measured component weights. The published total weight is a coherence check; differences between the sums and the actual weight must not be hidden. Encapsulation density, air gap and transformer quality are ND without manufacturer data or measurements.

2.5b — Photo-based estimated weight breakdown: hypotheses and limits

Documented basis: Jadis Ôde 25 kg according to its official data sheet; Acronos M-1 14 kg according to JC Valvular and RS-1 approximately 14 kg according to commercial documentation. Photography allows the chassis and transformer layout to be recognised, not the internal mass, the air gap, the core cross-section, the amount of resin or the electrical quality to be measured. The V14.01 estimates are retained to audit their coherence, not as a real cost breakdown.

ComponentÔde: V14.01 hypothesisRS-1: V14.01 hypothesisStatus
Chassis and enclosure10 kg5.75 kgPROBABLE; not weighed
Valves0.48 kg0.35 kgApproximate CALCULATED
Power transformer8.5 kg3.75 kgPROBABLE; no dimensional data sheet
Two output transformers6.0 kg5.0 kgPROBABLE; not weighed or tested
Encapsulation/resin1.3 kg0 kgPROBABLE; filling not verified
Wiring and fixings1.2 kg1.0 kgPROBABLE
Total of hypotheses27.48 kg versus 25 kg documented (deviation +2.48 kg; +9.9%)15.85 kg versus 14 kg declared (deviation +1.85 kg; +13.2%)The sums do not validate each component

What if Acronos used two hypothetical 5.5 kg OPTs?

Under the unverified assumption of 5 kg currently per pair, replacing them with 11 kg would add 6 kg. If another 1.2 kg of encapsulation were added: 14 + (11−5) + 1.2 = 21.2 kg. This scenario starts from the declared 14 kg weight; it must not be combined with the 15.85 kg hypothetical breakdown. It does not demonstrate better bass response, lower distortion or a particular manufacturing cost.

Limited conclusion: 25 kg and 14 kg describe the complete unit, not the performance of its transformers. Evaluating OPTs requires measurements of primary inductance, winding resistance, saturation/THD at low frequency and response under load.
ANNEX D — PRICES AND ECONOMIC SCENARIOS

Annex D — Prices and economic models

Separation of evidence: sale prices only when documented and dated; discounts subject to verification; cost breakdowns, margins and transfer prices are hypothetical scenarios and not accounting data from Jadis, Lyric or JC Valvular.

D.1 Value chain and price: hypotheses, markups and margins

Two levels of evidence: (1) announced or communicated prices, whose validity must be verified; (2) an illustrative financial model without access to invoices, actual manufacturing costs, contracts or discount conditions. No actual margins are attributed to Jadis, JC Valvular or Lyric Audio.

ModelPrice incl. VAT used as referenceOrigin and statusBase excl. VAT at 21%
Jadis Ôde€7,990Price announced by the dealer in the previous version; check current offer REPORTED-EXT€6,603.31
Acronos M-1€1,700Author's indication; not validated as official RRP ND official€1,404.96
Acronos RS-1€2,400Author's indication; not validated as official RRP ND official€1,983.47
Jadis with 30% discount€5,593Conditional scenario = 7,990×0.70. The code is not proven to apply to the model in the actual purchase CALCULATED€4,622.31

Markup and margin model (not real accounting)

The V14.01 example is retained: if a manufacturer had a hypothetical cost of €2,600 and applied a 35% markup on cost, the price would be 2,600×1.35 = €3,510 excluding VAT. Its gross margin on sales would be (3,510−2,600)/3,510 = 25.93%, not 35%. If a 35% gross margin were desired, the required price would be 2,600/(1−0.35) = €4,000. No figure proves costs or supply prices for Jadis.

Example hypothesisOperationResultCorrect interpretation
Hypothetical factory price€2,600 × 1.35€3,51035% markup on cost
Corresponding gross margin(3,510−2,600)/3,51025.93%Margin on sales, different from markup
Price if gross margin = 35%2,600/(1−0.35)€4,000Not to be confused with €3,510
Hypothetical 30% discount7,990×0.70€5,593Does not prove the code applies
Price ratio with hypothetical discount5,593/2,4002.33×Comparison valid only if prices and discount are effective
What cannot be deduced: the dealer's purchase cost, Lyric's margin, actual manufacturing cost, Jadis's hypothetical direct price, or that weight or encapsulation explains a precise RRP difference. The existence of discounts does not prove a pre-designed commercial "cushion" either.
Exercise retained from V14.01, reformulated: a distribution channel may apply markups of different sizes, logistics costs and after-sales service; a direct sale may avoid some of them. Without contracts and cost breakdowns it is not possible to quantify how much of the price difference corresponds to channel, manufacturing, taxes, warranties, marketing or positioning. In a scenario analysis these parameters must be stated separately and never presented as verified business figures.

Annex E — Glossary

Architecture and transformers

  • Single-ended (SE): one power valve per channel. The output transformer (OPT) sees a constant DC current (130 mA in the RS-1) and needs an air gap (gap) of ND dimension to avoid saturation. Heavier per watt than PP, with an advantage in second-harmonic purity.
  • Push-pull (PP): two valves per channel in phase opposition. The DC currents cancel (Φnet=0) and, in the ideal model, the OPT needs no gap; lower Zout and real bass control ND. Jadis Ôde 4×KT120 (2 per channel).
  • Ultralinear (UL): screen grid (g2) connected to a primary centre tap of the OPT. A compromise between triode (low distortion) and pentode (power). M-1, RS-1 and Ôde declare UL.
  • OPT: Output Transformer. Matches the high valve impedance to the low speaker impedance (4/8 Ω). SE has a gap, PP does not.
  • PT: Power Transformer. Converts 230 V to high-voltage B+ and filaments. Internal masses of the Jadis and Acronos ND; declared consumption does not equal transformer mass.
  • Gap: air gap in an EI core for SE. Prevents DC saturation but reduces inductance and increases weight.
  • Potting / Resin encapsulation: OPT encapsulation can attenuate vibration; it does not by itself determine electrical performance. Resin mass per OPT ND. Acronos varnished EI without potting.
  • Class A: valve conducts 360° of the cycle. Maximum linearity, maximum consumption and heat. Ôde, M-1 and RS-1 declare class A pure.
  • Class B / AB: each valve conducts 180° (B) or >180° (AB). More efficient, less heat than A.

Feedback and control

  • NFB (Negative Feedback): negative feedback. Part of the output returns to the input to reduce distortion and Zout. The RS-1 declares DF 50, which would imply deep NFB, but the depth and type are ND.
  • DF (Damping Factor): damping factor = Zload / Zout. DF 50 into 8 Ω → Zout 0.16 Ω. Into 4.9 Ω it would be ~30.6 if Zout were constant, but Zout varies with frequency.
  • Zout: amplifier output impedance. Low Zout = better cone control. Zout versus frequency remains to be measured.
  • Zmin / EPDR: minimum speaker impedance and Equivalent Peak Dissipation Resistance (impedance seen by the amp with phase). MR-A-01 simulated Zmin ~4.9 Ω; generic EPDR 2–3 Ω example of a difficult speaker.

Valves

  • KT120: power tetrode/pentode, 60 W plate dissipation. Jadis uses 4, M-1 uses 2 (1 per channel). ~100 g, current production.
  • KT150: KT120 evolution, 70 W plate, larger (145 mm high, ~125 g). RS-1 uses 2 (1 per channel).
  • ECC83 / 12AX7: high-gain dual triode (mu 100). Classic preamp valve, wide stock.
  • ECC82 / 12AU7: low-gain dual triode (mu 17), higher current. Driver in Ôde.
  • 12AT7: medium-gain dual triode (mu 60), higher current than 12AX7. NOS driver in M-1.
  • EC86: low-gain, low-noise RF triode. NOS preamp in RS-1, scarce.
  • ECC803S: premium low-noise ECC83 version. Driver + cathode follower in RS-1, NOS.
  • Bias: power valve quiescent current. RS-1 declares 130 mA per KT150 adjustable. Ôde automatic bias.
  • B+: high-voltage supply to the stage; ND without measurement. The 385 V calculation refers to idealised excursion, not B+.

Measurements and acoustics

  • THD: Total Harmonic Distortion. RS-1 declares 18 W @0.01% and 25 W @0.5% THD at 1 kHz, without a full curve.
  • RMS: continuous effective value. 18 W RMS @0.01% THD.
  • SPL: Sound Pressure Level in dB. 89 dB/W/m = speaker delivers 89 dB with 1 W at 1 m.
  • dB: decibel, logarithmic scale. +3 dB = double power, +10 dB = approximately double perceived loudness.
  • Headroom: power reserve above the average level. Report scenario 80 dB continuous + 15 dB crest = 95 dB peak → needs ~18 W, with +3 dB reserve → 35.8 W target.
  • Crest: peak-to-average difference of music. 15 dB typical in acoustic music.
  • Sensitivity: speaker dB/W/m. JC Valvular recommends ≥90 dB for SE as an orientation criterion, not a universal boundary.
  • Apparent vs real power: 25 W @0.5% THD is not equivalent to 25 W at a comparable distortion threshold. 18 W @0.01% is a low-distortion figure.

Construction and price

  • Stainless vs steel chassis: Jadis publishes a total mass of 25 kg and 430×370×220 mm; Acronos publishes ≈14 kg. The separate chassis weight is ND; do not infer rigidity or performance from estimated mass.
  • Craftsman margin: hypothesis of a 35% markup on cost, equivalent to a 25.93% gross margin on sales; it does not inform about real business margins.
  • Lyric markup: not documented: the real purchase cost and applicable discount are ND. The old figures were hypothetical scenarios, not verified margins.
  • Net RRP / incl. VAT: net = excl. VAT (RRP/1.21), incl. VAT = with 21% Spanish VAT. Example: €4,622 net → €5,593 incl. VAT.
  • ND / CONFIRMED / REPORTED-EXT / PROBABLE / CALCULATED: traceability labels of template V9.1.1: ND not determinable without schematic/measurement, CONFIRMED official documentation or direct manufacturer communication, REPORTED-EXT reliable third party without independent verification, PROBABLE unverified inference, CALCULATED with explicit formula.
Jadis Ôde vs Acronos M-1 and RS-1 · Technical report V14.03.2 · Nov 2026 · nauscopio